Concrete contractor in Santa Fe Springs, CA - slabs built from the base up

Quickset Downey Concrete Company pours driveways, patios, walks, steps and foundations for homeowners in Santa Fe Springs, CA. We're a concrete contractor based nearby in Downey, and I'm on site with our crew on every job.

Request an estimate (562) 414-1029

Smooth concrete driveway extends from a stone-and-siding house with three garage doors.

What Santa Fe Springs homeowners want from new concrete

Most calls we get start with something you can see: a driveway cracked across the middle, a patio that's sunk at one corner, or water pooling against the house after the sprinklers run. Usually the top of the slab didn't fail on its own. The subgrade it sits on was raked level instead of dug out and packed, so the slab settled with the dirt.

What moves the price is mostly work you won't see later: how much old concrete comes out, how deep we dig and pack the base, the steel inside the slab and the finish on top. The schedule turns on whether the city wants a permit and an inspection, and on curing, the days a new slab needs to gain strength before it carries weight. Your written estimate spells out each part.

If the budget gets tight, I'd rather keep the base and go simpler on the finish, because a good-looking slab on soft ground cracks anyway. The same goes for bigger work like foundation installation, where the footings and steel matter more than anything you'll see once it's done.

Concrete work we do in Santa Fe Springs

How a Santa Fe Springs job runs

Tell us about it
Call or send a message about what you've got, whether it's a cracked driveway, a sinking patio or a new slab, and we'll set a time for me to come out.
I measure and write it up
I come out, measure, look at the old concrete and where the water runs, then write an estimate that spells out the base, forms, steel and finish.
Permit, prep and the pour
Once you say yes, we pull any permit the job needs, build the base and forms, get them inspected, then pour, finish and clean up.

What we plan for on a Santa Fe Springs job

On a Santa Fe Springs job, I start by looking at what else stands on the lot. The city wants a separate permit worksheet for each detached structure, so if we're pouring a slab for a detached garage and another for a workshop, I set them up as two jobs on paper even when the crew builds them together.

Breaking out an old driveway leaves a lot of broken concrete, and the city sets a goal to reuse or recycle at least 75% of project waste, with a recycling form approved before a permit is issued. Storing material or directing traffic in the street takes a separate right-of-way permit, and its inspections can only be scheduled with a city contractor code and an approved permit number.

We're a concrete contractor based in Downey, CA, and we work across the cities around it, including Norwalk and Pico Rivera. When you're ready, call (562) 414-1029 or send the form to ask for an estimate.

Request an estimate

Tell us about your Santa Fe Springs job

Tell us what's there now and what you want poured. We reply within one business day to set up a free on-site estimate, with no obligation to go ahead.

Concrete patio beneath a timber pergola beside a red-brick house, with a smooth light-gray floor.

What Santa Fe Springs homeowners ask us for

Driveways torn out and replaced from the base up
Patios that drain away from the house
Walkways and steps with clean, straight edges
Garage floor slabs poured level
Stamped and decorative patio finishes
Footings and slabs for new structures

Other cities we work in

Why Santa Fe Springs homeowners call us

I come out to every job, measure it and write the estimate myself, and I'm on site with my crew when we do the work. That's how the layout stays exact and the lines come out clean. We're licensed and insured, and every job is backed by our satisfaction guarantee.

You're living there while we work, so we protect the yard, keep the mess off your lawn and keep a path to your door where we can. If I don't know something yet, like what's under the old slab, I'll say so instead of guessing. Call (562) 414-1029 when you're ready to talk it through.

Santa Fe Springs concrete questions

Do I need a permit for a concrete driveway in Santa Fe Springs?

The city's list of work that needs no construction permit doesn't name driveways or patios, so ask before any work starts. The city's Building and Safety Division issues permits for new work, repairs and demolition, and you can ask about your project at (562) 868-0511 ext.7560. When a permit's needed, we pull it and set up the inspections.

Can a homeowner pull their own permit in Santa Fe Springs?

Yes, city guidance says a homeowner can get a permit, and so can any contractor licensed by the State of California. The permit needs either workers' compensation insurance, which an owner who hires help may have to buy, or an Owner-Builder Statement saying you've hired no one. When you hire us, we pull it as the licensed contractor.

What building codes does Santa Fe Springs use for concrete work?

Santa Fe Springs currently works under the 2025 California codes, including the building, residential and green building codes. Those are the rules our forms, footings and rebar, the steel that ties a slab together, get checked against at inspection, so we build to them from the start.

Will my new concrete driveway crack like the old one?

A new slab can still crack, but a well-built one cracks where we planned it to. We dig out and pack the base so the slab has firm ground under it, set steel inside and cut control joints, grooves that give a crack a straight place to run, before the concrete sets hard. We also plan pours around midday heat, which leaves a weak, dusty top.